24小時加固服務熱線：134-02000333
Injection Method for CLB Project Concrete Structure Crack
CLB工程混凝土板結構裂紋修補方案-注射法
1. General Description for Crack:
裂紋概述
Some CLB project concrete panels have cracked due to the support stools in the stacks of panels not being aligned by ZPMC. Larger cracks have occurred where upper stools are outside the lower stools and the cantilever end of the loaded panel bends down and the top surface goes into tension where there are only N20 – 150 bars.
由于ZPMC使用不當?shù)姆椒ǘ询BCLB混凝土預制塊從而導致其中一些板塊出現結構裂紋。這些裂紋主要由于混凝土上表面受到堆疊位置不當?shù)膲|塊所產生的負彎矩所產生的拉應力而形成，且主要集中在配筋截面為N20-150 bars。
The crack widths have reduced when stack load is released and we think these cracks from bending will close up further when placed on the topside modules because the cracks are about 3m in from the end or middle span, and this area will sag under its own weight and close up the top of the slab.
當混凝土上表面的堆積荷載釋放時，這些結構裂紋的寬度有明顯縮小。當這些混凝土板被吊裝至模塊上時，由于受到自重荷載的影響，混凝土的上表面會進一步受壓從而可使裂紋進一步的閉合。
After investigation by SKM & ZPMC team, we found the cracks were only 5 – 10mm deep only. This implies the crack is shallow and the tension in the concrete only caused cracking in the outer surface of the slab. Thus the cracks are only surface and not affecting the effective section or strength.
在對這些裂紋進行調查之后，SKM及ZPMC的工程師發現這些裂紋的深度僅在5-10mm之間。這表明由于堆疊不當所引起的裂紋只出現在混凝土的外表面，且深度不深。因此這些裂紋不會影響截面的有效性或強度。
In accordance with AS3735 and British Standards it is acceptable to have cracks up to 0.1mm in a marine environment, therefore it is acceptable to have cracks less than 0.1mm with no treatment. Cracks wider than 0.1mm require an injection system to penetrate the crack and to reduce the risk to corrosion of reinforcement.
根據澳洲標準AS3735及英國規范，海洋工程可以接受寬度為0.1mm的裂紋，因此SKM接受那些寬度小于0.1mm的裂紋，且不要進行任何修補。對于寬度大于0.1mm的裂紋需用注射法使修補漿液完全滲入裂紋以減少鋼筋被腐蝕的風險。
Patching Process:
修補工藝：) Work Team:施工隊伍) Patching Material:
修補材料
a. Patching Glue:
